A.proxy
B.dual-stack
C.tunneling
D.dot1q
您可能感興趣的試卷
你可能感興趣的試題
A.user EXEC mode
B.global configuration mode
C.privileged EXEC mode
D.auxiliary setup mode
A.Router(config)#router ospf 1
B.Router(config)#router ospf 0
C.Router(config)#router ospf area 0
D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E.Router(config-router)#network 192.168.16.0 0.0.0.255 0
F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Refer to the exhibit.S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology. While testing this configuration, a technician notes that pings are successfully from hosts on the 172.16.1.0/24 network to hosts on both the 172.16.2.0/25 and 172.16.0.2.128/25 networks. However, pings between hosts on the 172.16.2.0/25 and 172.16.2.128/25 network are not successful. What could explain this connectivity problem?()
A.The ip subnet-zero command has been issued on the R1 router.
B.The RIPv2 dynamic routing protocol cannot be used across a Frame Relay network.
C.Split horizon is preventing R2 from learning about the R3 networks and R3 from learning about R2 networks.
D.The 172.16.2.0/25 and 172.16.2.128/25 networks are overlapping networks that can be seen by R1,but not between R2 and R3.
E.The 172.16.3.0/29 network used on the Frame Relay links is creating a discontiguous network between the R2 and R3 router subnetworks.
A.when a packet is received from an 802.1Q trunk,the vlan id can be determined from the source MAC address table
B.unkown unicast frames are retransmitted only to the ports that belong to the same vlan
C.ports between switches should be configured in access mode so that vlans can span across the ports
D.broadcast and multicast frames are retransmitted to ports that are configured on different vlan.
A.to provide routing to a local web server
B.to provide routing from an ISP to a stub network
C.to provide routing that will override the configured dynamic routing protocol
D.to provide routing to a destination that is not specified in the routing table and which is outside the local network
最新試題
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2?()
請參見圖示。網絡技術人員使用圖中所示的連接將主機A 連接到路由器以創建初始配置。下列有關此連接的陳述中哪一項正確?()
何時必須使用clock rate 命令配置路由器串行接口?()
請參見圖示。主機A 嘗試與主機C 建立TCP/IP 會話。在嘗試期間,路由器Y 的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為172.16.1.5而目的IP 地址為172.16.7.24的數據包。捕獲該幀時,它的源MAC 地址是什么?()
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程?()
請參見圖示。當計算機A 向計算機D 發送幀時,哪些計算機會接收該幀?()
請參見圖示。從主機X 發出的到主機Y 的tracert 命令已成功。下列哪一項正確地反映了追蹤列表中顯示的中間網絡設備的順序?()
請參見圖示。在網絡中,PC1向PC2發送了一條消息。PC2收到的幀如圖所示。該幀中的哪一信息確定了正確的目的應用程序?()
請參見圖示。一臺主機正使用NAT 連接到Internet。下列哪三項IP 地址可實現此連接?()
OSI 模型的哪兩項功能在第2層實現?()