A.NCP
B.LCP
C.ISDN
D.DLCI
E.SLIP
您可能感興趣的試卷
你可能感興趣的試題
What can be determined from the line of show ip route output shown in the exhibit？（）
A. The next routing update can be expected in 35 seconds.
B. The IP address 10.10.10.6 is configured on S0/1.
C. The IP address 10.10.10.8 is configured on S0/1.
D. This route is using the default administrative distance.
E. The 10.10.10.8 network is two hops away from this router.
A.Microsegmentation decreases the number of collisions on the network.
B.if a switch receives a frame for an unkown destination,it uses ARP to resolve the address.
C.Spanning Tree Protocol allows switches to automatically share vlan information.
D.In a properly functioning network with redundant switched paths,each switched aegment will contain one root bridge with all its ports in the forwarding state.All other switches in that broadcast domain will have only one root port.
E.Establishing vlans increases the number of broadcast domains.
F.Switches that are configured with vlans make forwarding decisions based on both layer 2 and layer 3 address information.
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally， static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes？（）
A.Configure the no ip subnet-zero command on R1,R2,and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
Which destination addresses will be used by Host A to send data to Host C？（）
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router’s E0 interface
F. the MAC address of the router’s E0 interface
An administrator is unsuccessful in adding VLAN 50 to a switch. While troubleshooting the problem，the administrator views the output of the show vtp status command， which is displayed in the graphic. What commands must be issued on this switch to add VLAN 50 to the database？（）
A. Switch（config-if）# switchport access vlan 50
B. Switch（vlan）# vtp server
C. Switch（config）# config-revision 20
D. Switch（config）# vlan 50 name Tech
E. Switch（vlan）# vlan 50
F. Switch（vlan）# switchport trunk vlan 50
最新試題
在配置路由器時，網絡技術人員想要命名路由器。輸入hostname 命令后，技術人員會看到下列哪一項提示？（）
請參見圖示。圖中所示路由表所屬的PC 已正確配置。IP 地址192.168.1.254屬于哪一個網絡設備或接口？（）
下列哪些是私有IP 地址的地址范圍？（）
請參見圖示。主機X 和主機Y 與本地網絡的通信受到限制。此問題的原因是什么？（）
OSI 模型的哪兩項功能在第2層實現？（）
請參見圖示。從主機X 發出的到主機Y 的tracert 命令已成功。下列哪一項正確地反映了追蹤列表中顯示的中間網絡設備的順序？（）
何時必須使用clock rate 命令配置路由器串行接口？（）
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2？（）
請參見圖示。一臺路由器（其路由表如圖所示）收到發往192.168.1.4的數據包。路由器將如何處理該數據包？（）
請參見圖示。主機A 正在訪問多臺服務器。結合使用什么端口號和地址即可唯一識別特定服務器上運行的特定進程？（）