A.It checks the configuration register
B.It attempts to boot from a TFTP server
C.It loads the first image file in flash memory
D.It inspects the configuration file in NVRAM for boot instructions
您可能感興趣的試卷
你可能感興趣的試題
A.ipv6 host
B.ipv6 unicast-routing
C.ipv6 local
D.ipv6 neighbor
A.Executing password recovery is required.
B.The virtual terminal lines are misconfigured.
C.Use Telnet to connect to RouterA and then to NewSwitch to correct the error.
D.Power cycle of NewSwitch will return it to a default configuration.
Refer to the exhibit.This command is executed on 2960Switch：
2960Switch（config）# mac-address-table static 0000.00aa.aaaa vlan 10 interface fa0/1
Which two of these statements correctly identify results of executing the command？（）
A.Port security is implemented on the fa0/1 interface.
B.MAC address 0000.00aa.aaaa does not need to be learned by this switch.
C.Only MAC address 0000.00aa.aaaa can source frames on the fa0/1 segment.
D.Frames with a Layer 2 source address of 0000.00aa.aaaa will be forwarded out fa0/1.
E.MAC address 0000.00aa.aaaa will be listed in the MAC address table for interface fa0/1 only.
A.255.255.255.240
B.255.255.255.254
C.255.255.255.252
D.255.255.255.0
E.255.255.255.248
A.A more efficient use of bandwidth can be achieved allowing many physical groups to use the same network infrastructure
B.Broadcast storms can be mitigated by decreasing the number of broadcast domains,thus increasing their size.
C.A higher level of network security can be reached by separating sensitive data traffic from other network traffic.
D.Port-based vlans increase switch-port use efficient,thanks to 802.1Q trunks
E.A more efficient use of bandwidth can be achieved allowing many logical networks to use the same network infrastructure.
F.Broadcast storms can be mitigated by increasing the number of broadcast domains,thus reducing their size.
G. VLANs make it easier for IT staff to configure new logical groups,because the vlans all belong to the same broadcast domain.
最新試題
OSI 模型的哪兩項功能在第2層實現？（）
請參見圖示。圖中所示路由表所屬的PC 已正確配置。IP 地址192.168.1.254屬于哪一個網絡設備或接口？（）
下列哪些是私有IP 地址的地址范圍？（）
在配置路由器時，網絡技術人員想要命名路由器。輸入hostname 命令后，技術人員會看到下列哪一項提示？（）
請參見圖示。網絡中的所有設備均使用默認配置。此拓?fù)渲行枰嗌賯€邏輯地址范圍？（）
請參見圖示。RouterB 已經過正確配置。RouterA 的以太網接口Fa0/0已使用如圖所示的命令進行配置。但是，從RouterA 的Fa0/0接口無法成功ping 通RouterB 的Fa0/0接口。應在RouterA 上采取什么措施來解決此問題？（）
請參見圖示。一臺路由器（其路由表如圖所示）收到發往192.168.1.4的數據包。路由器將如何處理該數據包？（）
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2？（）
在路由器上使用Router#copy running-config startup-config 命令會產生什么效果？（）
PC 無法連接到任何遠程網站，無法ping 通其默認網關，也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常？（）