Nexus7000# config t
Nexus700（config）# interface ethernet 2/11
Nexus700（config-if）# switchport mode private-vlan host
Nexus700（config-if）# switchport private-vlan host-association 14 50
Nexus700（config-if）# exit
Nexus700（config）#
What will this command sequence achieve？（）
A. associate interface E2/11 to community VLANs 14 and 50
B. associate interface E2/11 to secondary VLANs 14 and 50
C. associate interface E2/11 to primary VLAN 50 and secondary VLAN 14
D. associate interface E2/11 to primary VLAN 14 and secondary VLAN 50
您可能感興趣的試卷
你可能感興趣的試題
A. Port priority value can be configured between 1 and 65535.
B. A higher port priority value means a higher priority of LACP.
C. Port priority can be configured so that specific links can be chosen as active links rather than the hot standby links within the port channel.
D. LACP uses the port priority with the port number to form the port identifier.
E. LACP Port priority default value should always be changed
A. Cisco AV-pair
B. TACACS+ or RADIUS ack frame role attribute
C. DH-CHAP challenge attribute
D. privilege level attribute
A. Graceful consistency check is enabled by default.
B. When graceful consistency check is enabled， only the links on the secondary peer device are suspended.
C. Graceful consistency check is disabled by default， so to enable this feature， use graceful consistency-check command under VPC domain configuration mode.
D. When graceful consistency check is enabled， only the inconsistent VLANs on the secondary peer device are suspended.
A. A single VACL can be shared across two or more VDCs.
B. Use of VACLs requires no special license to be installed.
C. VACLs make use of IP or MAC ACLs.
D. Only options drop and forward are permitted.
A. Adjacency Server is required when OTV is deployed with unicast-only transport.
B. Adjacency Server is required when OTV is deployed with multicast-enabled transport.
C. Each OTV device wishing to join a specific OTV logical overlay needs to first register with the Adjacency Server.
D. Each OTV device trying to join a specific OTV logical overlay needs to be configured as an Adjacency Server.
最新試題
Application Control Engine （ACE） can check the health of servers and server farms by configuring health probes （which are sometimes referred to as keepalives）. A probe can be one of many types. Which are valid ACE probes？ （）
Given the following output： san-port-channel 12 is up Hardware is Fibre Channel Port WWN is 24：0c：00：0d：ec：d3：5c：00 Admin port mode is NP， trunk mode is on Port mode is NP Port vsan is 1 Speed is 8 Gbps Member[1] ： fc2/3 Member[2] ： fc2/4 What does "Speed is 8 Gbps" indicate？（）
On a Cisco Unified Computing System （UCS）， which two statements regarding Ethanalyzer are true？（）
A Cisco UCS fabric interconnect in end-host mode learns MAC addresses on which port types？（）
A Cisco Application Control Engine Appliance （ACE） non-admin context does not support "sticky" configuration. What is the reason for this issue？（）
Refer to the exhibit.The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）. Which actions might be used to change this behavior？（）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
From the Cisco UCS CLI， how do you verify which uplink ports a blade server is using for its network connectivity？（）