A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
您可能感興趣的試卷
你可能感興趣的試題
The network administrator is adding a new N1Kv to the vCenter， however， the administrator does not see the new switch under the networking tab of vCenter.
The administrator issues the following command on the VSM to troubleshoot：
VSM# show svs connections
connection VC：
ip address： 10.10.10.30
remote port： 80
protocol： vmware-vim https
certificatE. default
datacenter namE. DC1
DVS uuiD. 67 32 30 50 a6 d2 49 64-9e 1c 5f 49 e3 af 55 99
config status： Disabled
operational status： Disconnected sync status： -
version： -
When attempting to fix the issue， the following error is seen：
VSM-PRI-188# conf
VSM-PRI-188（config）# svs connection VC
VSM-PRI-188（config-svs-conn）# connect
ERROR： [VMWARE-VIM] Extension key was not registered before its use
What is the cause of the error？（）
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
Given the following configuration：
port-profile type ethernet DATA-UPLINK
vmware port-group
switchport trunk allowed vlan 1-3967，4048-4093
channel-group auto mode on
no shutdown
state enabled
port-profile type ethernet MGMT-UPLINK
vmware port-group
switchport trunk allowed vlan 10-12
channel-group auto mode on
no shutdown
state enabled
VEMs are seen to be joining and then are lost from the Cisco VSM. How would you resolve this issue？（）
A. Remove second NIC from each port profile
B. Remove VEM from VSM （no vem X）， remove NICs， and reinsert
C. Ensure that VLANs on uplink profiles are not overlapping
D. Reinstall VEM
E. Issue the command "module vem X execute vemcmd set pinning module vsm 1"
A. Send monitored traffic to a VLAN
B. Send monitored traffic to a remote VEM over L2
C. Receive monitored traffic on a vEthernet interface
D. Send monitored traffic to an IP destination
A. Source and destination interface must be on the same host
B. Source and destination interfaces can be on different hosts
C. Destination vEthernet interface can be on a different VLAN than the source
D. Destination interface can be a physical port
E. Destination interface cannot be a physical port
Given a host with two NICs assigned to a N1k profile，which topologies are suitable for this type of configuration （）
port-profile type Ethernet name VM-Data
vmware port-group
switchport mode trunk
switchport allowed vlan 400-410
channel-group auto mode active
no shut
state enabled
A. Cisco UCS fabric interconnects
B. Pair of N5K’s in VPC
C. Standalone N5K
D. Pair of N5K’s in non-VPC
E. Cisco Catalyst 6000 Switch in VSS
最新試題
In the event of a GSS failure in a GSS cluster， which is true？（）
Which of the following are supported in Cisco Global Site Selector？ （）
Refer to the exhibit.Your company requires a Cisco UCS configuration that will， at a minimum， allow the configuration in the provided exhibit. Which Cisco UCS components will meet the requirement？（）
When testing ICMP access to a functional load-balancing ACE VIP， it fails. What is the reason of this problem？ （）
Where are SAN Port Channel is created in UCS Manager？（）
Which GSS "source access list" is used to allow access to GSS by clients when GSS is being used as the DNS？（）
KAL-AP on the Cisco ACE allows communication with Cisco ACE Global Site Selector， to report virtual IP and real server availability. Which statement is true about KAL-AP？（）
A Cisco Application Control Engine Appliance （ACE） non-admin context does not support "sticky" configuration. What is the reason for this issue？（）
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
When will an "all configuration" backup be imported into the Cisco UCS Manager？（）