多項選擇題What are two reasons a network administrator would use CDP?()

A. to verify the type of cable interconnecting two devices
B. to determine the status of network services on a remote device
C. to obtain VLAN information from directly connected switches
D. to verify Layer 2 connectivity between two devices when Layer 3 fails
E. to obtain the IP address of a connected device in order to telnet to the device
F. to determine the status of the routing protocols between directly connected routers


您可能感興趣的試卷

你可能感興趣的試題

1.多項選擇題Which two locations can be configured as a source for the IOS image in the boot system command?()

A.RAM
B.NVRAM
C.flash memory
D.HTTP server
E.TFTP server
F.Telnet server

2.多項選擇題A network administrator is explaining VTP configuration to a new technician. What should the network administrator tell the new technician about VTP configuration?()

A. A switch in the VTP client mode cannot update its local VLAN database.
B. A trunk link must be configured between the switches to forward VTP updates.
C. A switch in the VTP server mode can update a switch in the VTP transparent mode.
D. A switch in the VTP transparent mode will forward updates that it receives to other switches.
E. A switch in the VTP server mode only updates switches in the VTP client mode that have a higher VTP revision number.
F. A switch in the VTP server mode will update switches in the VTP client mode regardless of the configured VTP domain membership.

3.多項選擇題Before installing a new, upgraded version of the IOS, what should be checked on the router, and which command should be used to gather this information?()

A. the amount of available ROM
B. the amount of available flash and RAM memory
C. the version of the bootstrap software present on the router
D. show version
E. show processes
F. show running-config

4.多項選擇題What can be done to secure the virtual terminal interfaces on a router?()

A. Administratively shut down the interface.
B. Physically secure the interface.
C. Create an access list and apply it to the virtual terminal interfaces with the access-group command.
D. Configure a virtual terminal password and login process.
E. Enter an access list and apply it to the virtual terminal interfaces using the access-class command.

5.多項選擇題Which of the following IP addresses can be assigned to the host devices?()

A.205.7.8.32/27
B.191.168.10.2/23
C.127.0.0.1
D.224.0.0.10
E.203.123.45.47/28
F.10.10.0.0/13

最新試題

Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?()

題型:單項選擇題

Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?()

題型:單項選擇題

Three access ports have been installed and configured to a small office.What term defines the wireless topology?()

題型:單項選擇題

A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?()

題型:單項選擇題

What is the subnetwork address for a host with the IP address 201.100.5.68/28?()

題型:單項選擇題

At which layer of the OSI model is RSTP used to prevent loops?()

題型:單項選擇題

How are VTP advertisements delivered to switches across the network?()

題型:單項選擇題

A network administrator is planning a network installation for a large organization.The design requires 100 separate subnetworks,so the company has acquired a Class B network address.What subnet mask will provide the 100 subnetworks required, if 500 usable host addresses are required per subnet?()

題型:單項選擇題

If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?()

題型:單項選擇題

Which statement describes the rule of split horizon?()

題型:單項選擇題