A. Hash address： Selects the server by using a hash value based on either the source or destination IP address， or both
B. Hash URL： Selects the server by using a hash value based on the requested URL
C. Hash MAC.Selects the server by using a hash value based on either the source or destination MAC address， or both
D. Hash header： Selects the server by using a hash value based on the HTTP header name
E. Hash IP： Selects the server using a hash value based on the IP address
您可能感興趣的試卷
你可能感興趣的試題
A. UCS-A# show pinning border-interfaces
B. UCS-B# show service-profile circuit
C. UCS-B（nxos）# show pinning server-interfaces
D. You must statically configure which uplink the blades should use， or you will not have connectivity.
A. An interface ’san-port-channel’ in NXOS
B. An interface ’port-channel’ in NXOS
C. An interface ’port-channel’ with ’mode fc’ configured
D. An interface ’fc-port-channel’ in NXOS
A. The fabric interconnects must be in end-host mode.
B. A pin group must be configured on the server tab in Cisco UCS Manager.
C. In the service profile for Server 1， vNIC 1 must be explicitly assigned to a pin group.
D. Server 1 cannot be configured to meet the requirement. A server can only be manually pinned to a single physical interface and not a port channel because of the LACP load-balancing algorithm.
E. Server 1 cannot be configured to meet the requirement. A server is either manually pinned to an uplink on both fabric interconnects or the server is automatically pinned， but not both.
Refer to the exhibit.
The Cisco UCS domain is operating in switching mode. A network administrator notices that no traffic is traversing the uplinks on Fabric Interconnect B （Path C）.
Which actions might be used to change this behavior？（）
A. Fix the port channel configuration between Fabric Interconnect B and Nexus 5548 B as the port channel IDs do not match.
B. Modify the bridge priority on the fabric interconnects so that one of the Nexus 5548s will always be the root bridge.
C. Modify the bridge priority on the Nexus 5548s so that one of them will always be the root bridge.
D. Modify the port priorities on the fabric interconnect uplinks （Paths B and C） so that they are a higher priority than ports Eth1/4 and Eth1/9 （Path D）.
E. This is an invalid configuration as Cisco UCS fabric interconnects cannot be directly connected.
Refer to the exhibit.
According to the equipment tab in Cisco UCS Manager， which is true？（）
A. A is an uplink port， B is a fabric port， C is a server port， D is a backplane port， E is a DCE interface， and F is a vNIC
B. A is an uplink port， B is a server port， C is a fabric port， D is a backplane port， E is a DCE interface， and F is a vNIC
C. A is an uplink port， B is a fabric port， C is a backplane port， D is a server port， E is a DCE interface， and F is a vNIC
D. A is an uplink port， B is a server port， C is a fabric port， D is a DCE interface， E is a backplane port， and F is a vNIC
E. A is an fabric port， B is a downlink port， C is an uplink port， D is a server port， E is a VIC interface， and F is a vNIC
最新試題
Where are SAN Port Channel is created in UCS Manager？（）
Which three statements are possible causes for the "fltAdaptorHostIfLink-down" fault in UCS Manager？ （）
What is the appliance port used to connect to in a Cisco Unified Computing System？（）
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）
In the event of a GSS failure in a GSS cluster， which is true？（）
Which statement is true regarding Backup tasks in Cisco UCS？（）
Refer to the exhibit. According to the equipment tab in Cisco UCS Manager， which is true？（）
Which statement is true about "full state backup" in a Cisco Unified Computing System？（）
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）