A. enbale password c1sco
B. secret enable c1sco
C. password enable c1sco
D. enable secret c1sco
您可能感興趣的試卷
你可能感興趣的試題
A. An IPv6 address is 64 b long and is represented as hexadecimal characters.
B. An IPv6 address is 32 b long and is represented as decimal digits.
C. An IPv6 address is 128 b long and is represented as decimal digits.
D. An IPv6 address is 128 b long and is represented as hexadecimal characters.
A. The new IOS image is too large for the router flash memory.
B. The TFTP server is unreachable from the router.
C. The new IOS image is not correct for this router platform.
D. The IOS image on the TFTP server is corrupt.
E. There is not enough disk space on the TFTP server for the IOS image.
This graphic shows the results of an attempt to open a Telnet connection to router ACCESS1 from router Remote27. Which of the following command sequences will correct this problem? （）
A. ACCESS1(config)# line console 0 ACCESS1(config-line)# password cisco
B. Remote27(config)# line console 0 Remote27(config-line)# login Remote27(config-line)# password cisco
C. ACCESS1(config)# line vty 0 4 ACCESS1(config-line)# login ACCESS1(config-line)# password cisco
D. Remote27(config)# line vty 0 4 Remote27(config-line)# login Remote27(config-line)# password cisco
E. ACCESS1(config)# enable password cisco
F. Remote27(config)# enable password cisco
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?（）
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
A. A remote physical layer problem exists.
B. The host NIC is not functioning.
C. TCP/IP has not been correctly installed on the host.
D. A local physical layer problem exists.
最新試題
On which options are standard access list based?（）
Which pairing reflects a correct protocol-and-metric relationship?（）
An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?（）
What is the default administrative distance of OSPF?（）
Which statement describes the rule of split horizon?（）
What is the subnetwork address for a host with the IP address 201.100.5.68/28?（）
Which Cisco IOS diagnostics command can disrupt the operation of a router under high-load conditions?（）
A network administrator needs to configure a serial link between the main office and a remote location.The router at the remote office is a non-cisco router. How should the network administrator configure the serial interface of the main office router to make the connection?（）
The network administrator cannot to switch 1 over a telnet session,although the hosts attached to switch 1 can ping the interface Fa0/0 of the router.Given the information in the graphic and assuming that the router and switch2 are configured properly,which of the following commands should be issued on switch 1 to correct this problem?（）
While troubleshooting a network problem,a technician discovers that the current copy of the Cisco IOS is outdated and needs to be updated.Which of the following commands would the technician issue to replace the Cisco router IOS with the newer version?（）