Which of the following specification will allow you to： associate VLAN groups to STP instances so you can provide multiple forwarding paths for data traffic and enable load balancing？ （）
A. IEEE 802.1d （STP）
B. IEEE 802.1s （MST）
C. IEEE 802.1Q （CST）
D. IEEE 802.1w （RSTP）
您可能感興趣的試卷
你可能感興趣的試題
Which of the following specifications is a companion to the IEEE 802.1w Rapid Spanning Tree Protocol （RSTP） algorithm， and warrants the use multiple spanning-trees？ （）
A. IEEE 802.1s （MST）
B. IEEE 802.1Q （CST）
C. Cisco PVST+
D. IEEE 802.1d （STP）
E. None of the other alternatives apply
pany uses MSTP within their switched LAN.
What is the main purpose of Multiple Instance Spanning Tree Protocol （MSTP）？（）
A. To enhance Spanning Tree troubleshooting on multilayer switches
B. To reduce the total number of spanning tree instances necessary for a particular topology
C. To provide faster convergence when topology changes occur in a switched network
D. To provide protection for STP when a link is unidirectional and BPDUs are being sent but not received
E. None of the other alternatives apply
The Company network utilizes the Multiple-instance Spanning Tree protocol in its switched LAN.
Which three statements about the MST protocol （IEEE 802.1S） are true？ （）
A. To verify the MST configuration， the show pending command can be used in MST configuration mode.
B. When RSTP and MSTP are configured； UplinkFast and BackboneFast must also be enabled.
C. All switches in the same MST region must have the same VLAN-to-instance mapping， but different configuration revision numbers.
D. All switches in an MST region， except distribution layer switches， should have their priority lowered from the default value 32768.
E. An MST region is a group of MST switches that appear as a single virtual bridge to adjacent CST and MST regions.
F. Enabling MST with the "spanning-tree modemst" global configuration command also enables RSTP.
On switch R1 you issue the "udld enable" global command.
What does this command accomplish？ （）
A. Enables all fiber-optic LAN ports for Unidirectional LINK Detection （UDLD）
B. Enables all copper media LAN ports Unidirectional Link Detection （UDLD）
C. Overrides the default UDLS setting for all ports
D. Globally enables all ports on the device for Unidirectional Link Detection （UDLS）
E. None of the other alternatives apply
Switch R1 has been configured with the root guard feature.
What statement is true if the spanning tree enhancement Root Guard is enabled？ （）
A. If BPDUs are not received on a non-designated port， the port is moved into the STP loop- inconsistent blocked state
B. IF BPDUs are received on a PortFast enabled port， the port is disabled.
C. If superior BPDUs are received on a designated port， the interface is placed into the root- inconsistent blocked state.
D. If inferior BPDUs are received on a root port， all blocked ports become alternate paths to the root bride.
最新試題
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
What two things will occur when an edge port receives a BPDU？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）