A. The i nterface used by one router to connect to the other router is passive in the EIGRP process.
B. Duplicate EIGRP router IDs.
C. Mismatched Hold Timers.
D. IP addresses of 10.1.1.1/24 and 10.2.2.2/24, respectively.
您可能感興趣的試卷
你可能感興趣的試題
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1's (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode.
Which of the following occurs？（）
A.Fa0/0 fails
B.The command is rejecteD
C.The existing three neighbors fail
D.The neighborship with 172.16.2.20 fails and then reestablishes
E.None of the other answers is correct
Routers R1 and R2, currently EIGRP neighbors over their Fa0/0 interfaces (respectively),both use EIGRP authentication. Tuesday at 8 p.m. the neighborship fails.
Which of the following wo uld not be useful when investigating whether authenticationhad anything to do with the failure？（）
A. debug eigrp packet
B. show key chain
C. show ip eigrp neighbor failure
D. show clock
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration.
Which of the following is true regarding the results from this c hange？（）
A.The show ip eigrp neighbors command on R1 lists the revised Hello timer
B.The show ip eigrp interfaces command on R1 lists the revised Hello timer
C.The R1 - R2 neighborship fails due to Hello timer mismatcH
D.The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2.
Which answer gives the reason for the omission？（）
A. R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.
B. S0/2 may currently be in a state other than up/up.
C. The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.
D. S0/2 may be configured as a passive inter face.
A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface.
Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）
A. 172.16.0.1/23
B. 172.16.1.1/26
C. 172.16.1.1/24
D. 172 .16.0.255/23
E. None of the other answers is correct.
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）