On a 3550 EMI switch，
which three types of interfaces can be used to configure HSRP？ （）
A. Loopback interface
B. SVI interfac
C. Routed port
D. Access port
E. EtherChannel port channel
F. BVI interface
您可能感興趣的試卷
你可能感興趣的試題
Which command will need to be added to External_A to ensure that it will take over if serial 0/0 on External_B fails？ （）
A. standby 1 priority 130
B. standby 1 preempt
C. standby 1 track fastethernet 0/0
D. standby 1 track 10.10.10.1
You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails.
What command would you use if you wanted to configure this？ （）
A. en standby preempt
B. standby preempt enable
C. standby preempt
D. hot standby preempt
A. Define the encapsulation type.
B. Define the standby router.
C. Define the standby IP address.
D. Enable the standby priority.
Refer to the exhibit. HSRP has been configured and Link A is the primary route to router R4. When Link A fails， router R2 （Link B） becomes the active router.
Which router will assume the active role when Link A becomes operational again？" （）
A. The primary router R1 will reassume the active role when it comes back online.
B. The standby router R2 will remain active and will forward the active role to router R1 only in the event of its own failure.
C. The standby router R2 will remain active and will forward the active role to router R1 only in the event of Link B failure.
D. The third member of the HSRP group， router R3， will take over the active role only in event of router R2 failure.
Refer to the exhibit. The Gateway Load Balancing Protocol has been configured on routers R1 and R2， and hosts A and B have been configured as shown.
Which statement can be derived from the exhibit？（）
A. The hostA default gateway has been configured as 10.88.1.10/24.
B. The GLBP weighted load balancing mode has been configured.
C. The GLBP round-robin， load-balancing mode has been configured.
D. The GLBP host-dependent， load-balancing mode has been configured.
E. The hostA default gateway has been configured as 10.88.1.1/24.
F. The hostA default gateway has been configured as 10.88.1.4/24.
最新試題
Which two statements are true about BPDU port-guard and BPDU filtering？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Which statement is correct about RSTP port roles？（）
Which two statements are true when the extended system ID feature is enabled？ （）