You work as a network engineer for. You study the exhibit carefully. From the configuration sample shown of a Cisco Catalyst 3560 Series Switch，
what can you determine regarding Layer 3 routing functionality of the interface？（）
Exhibit：
A.The interface is configured correctly for Layer 3 routing capabilities.
B.The interface needs an additional configuration entry to enable IP routing protocols.
C.The interface subcommand ip routing is required to enable IP routing on the interface.
D.An SVI interface is required to enable IP routing for network 192.20.135.0.
您可能感興趣的試卷
你可能感興趣的試題
A new floor has been added to the enterprise campus network， providing client access for desktop PCs， laptops， and IP phones for employees and guests. During verification， a few desktop PCs have limited corporate access but not Internet access. Most other desktop PCs， all laptops， and IP phones are working correctly. Additional information indicates that the desktop PCs are obtaining IP host addresses from the DHCP server， which is intended for only the IP phones.
Where should troubleshooting about this connectivity issue be focused？（）
A.DNS
B.first-hop redundancy protocol
C.DHCP server and options
D.VLAN mapping
E.client network configuration
F.routing protocols
A new building has been added to the enterprise campus network， providing client access for desktop PCs， laptops， and IP phones for employees and guests. During verification， only a few laptops using
wireless are reported to have problems， while other desktops， IP phones， and most other wireless laptops are fully operational. Additional information received about the problem indicates that， while the problematic wireless laptops cannot reach internal corporate websites， they can reach the Internet.
Where should troubleshooting about this connectivity issue be focused？（）
A.client network configuration
B.VLAN mapping
C.routing protocols
D.first-hop redundancy protocol
You work as a network engineer for. You study the exhibit carefully. You have configured an interface to be an SVI for Layer 3 routing capabilities. Assuming that all VLANs have been correctly configured and based on the configuration example shown，
what can be determined？ （）
Exhibit：
A.Interface gigabitethernet0/2 will be excluded from Layer 2 switching and enabled for Layer 3 routing.
B.The interface is missing IP configuration parameters； therefore， it will only function at Layer 2.
C.The command switchport autostate exclude should be entered in global configuration mode， not sub-interface mode， to enable a Layer 2 port to be configured for Layer 3 routing.
D.The configured port is excluded in the calculation of the status of the SVI.
You have configured a Cisco Catalyst switch to perform Layer 3 routing via an SVI and have
assigned that interface to VLAN 20. To check the status of the SVI， you issue the show interfaces vlan 20 command at the CLI prompt. You see from the output display that the interface is in an "up/up" state.
What must be true in an SVI configuration to bring the VLAN and line protocol up？（）
A.The port must be physically connected to another Layer 3 device.
B.At least one port in VLAN 20 must be active.
C.The Layer 3 routing protocol must be operational and receiving routing updates from neighboring peer devices.
D.Because this is a virtual interface， the operational status will always be in an "up/up" state.
A.The best match of the ACL entries will be used for granularity of control.
B.They use source IP information for matching operations.
C.They use source and destination IP information for matching operations.
D.They use source IP information along with protocol-type information for finer granularity of control.
最新試題
Which statement is correct about RSTP port roles？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）