多項選擇題Which three statements are true of the Link Aggregation Control Protocol (LACP)?()

A.LACP is used to connect to non-Cisco devices.
B.LACP packets are sent with the command channel-group 1 mode desirable.
C.LACP packets are sent with the command channel-group 1 mode active.
D.Standby interfaces should be configured with a higher priority.
E.Standby interfaces should be configured with a lower priority.


您可能感興趣的試卷

你可能感興趣的試題

1.多項選擇題

Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network, Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit, 
which two statements are true?()

A.Changing the bridge priority of S1 to 4096 would improve network performance.
B.Changing the bridge priority of S1 to 36864 would improve network performance.
C.Changing the bridge priority of S2 to 36864 would improve network performance.
D.Changing the bridge priority of S3 to 4096 would improve network performance.
E.Disabling the Spanning Tree Protocol would improve network performance.
F.Upgrading the link between S2 and S3 to Gigabit Ethernet would improve performance.

2.多項選擇題Which two statements are true when the extended system ID feature is enabled? ()

A.The BID is made up of the bridge priority value(two bytes) and bridge MAC address (six bytes).
B.The BID is made up of the bridge priority (four bits), the system ID (12 bits), and a bridge MAC address (48 bits).
C.The BID is made up of the system ID (six bytes) and bridge priority value (two bytes).
D.The system ID value is the VLAN ID (VID).
E.The system ID value is a unique MAC address allocated from a pool of MAC addresses assigned to the switch or module.
F.The system ID value is a hex number used to measure the preference of a bridge in the spanning-tree algorithm.

3.多項選擇題

Based on the show spanning-tree vlan 200 output shown in the exhibit, 
which two statements about the STP process for VLAN 200 are true? ()

A.BPDUs will be sent out every two seconds.
B.The time spent in the listening state will be 30 seconds.
C.The time spent in the learning state will be 15 seconds.
D.The maximum length of time that the BPDU information will be saved is 30 seconds.
E.This switch is the root bridge for VLAN 200.
F.BPDUs will be sent out every 10 seconds.

5.多項選擇題Which three statements about STP timers are true?()

A.STP timers values (hello, forward delay, max age) are included in each BPDU.
B.A switch is not concerned about its local configuration of the STP timers values. It will only consider the value of the STP timers contained in the BPDU it is receiving.
C.To successfully exchange BPDUs between two switches, their STP timers value (hello, forward delay, max age) must be the same.
D.If any STP timer value (hello, forward delay, max age) needs to be changed, it should at least be changed on the root bridge and backup root bridge.
E.On a switched network with a small network diameter, the STP hello timer can be tuned to a lower value to decrease the load on the switch CPU.
F.The root bridge passes the timer information in BPDUs to all routers in the Layer 3 configuration.

最新試題

DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()

題型:單項選擇題

Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2?()

題型:單項選擇題

Which router redundancy protocol cannot be configured for interface tracking?()

題型:單項選擇題

Which statement is correct about the use of the virtual interface on a WLC ?()

題型:單項選擇題

Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result?()

題型:單項選擇題

Which two statements are true when the extended system ID feature is enabled? ()

題型:多項選擇題

Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port:00:06:34: %CDP-4-DUPLEX_MISMATCH: duplex mismatch discovered on FastEthernet0/5 (not half  duplex), with SW_A FastEthernet0/4 (half duplex) , with TBA05071417(Cat6K-B) 0/4 (half duplex). What would be the possible outcome of the problem?()

題型:單項選擇題

Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command, which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true?()

題型:單項選擇題

Which two statements about the various implementations of STP are true?()

題型:多項選擇題

What is the configured priority value of the Vlan105’s group on DS2 ?()

題型:單項選擇題