Refer to the exhibit.
What does the command channel-group 1 mode desirable do？ （）
A.enables LACP unconditionally
B.enables PAgP only if a PAgP device is detected
C.enables PAgP unconditionally
D.enables Etherchannel only
E.enables LACP only if a LACP device is detected
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA.
Which two statements are true about the possible result of attaching the second link？（）
A.The switch port attached to LinkB will not transistion to up.
B.One of the two switch ports attached to the hub will go into blocking mode when a BPDU is received.
C.Both switch ports attached to the hub will transition to the blocking state.
D.A heavy traffic load could cause BPDU transmissions to be blocked and leave a switching loop.
E.The switch port attached to LinkA will immediately transition to the blocking state.
A.All ports will temporarily transition to the learning state for a period equal to the max age timer plus the forward delay interval.
B.All ports will transition temporarily to the learning state for a period equal to the forward delay interval.
C.The default aging time for MAC address entries will be reduced for a period of the max age timer plus the forward delay interval.
D.The default hello time for configuration BDPUs will be reduced for the period of the max age timer.
A.The port immediately transitions to the Forwarding state.
B.The switch generates a Topology Change Notification （TCN） BPDU.
C.The port immediately transitions to the err-disable state.
D.The port becomes a normal STP switch port.
A.RSTP information is automatically aged out.
B.The port sends a TCN to the root bridge.
C.The port moves to listening state.
D.The port becomes a normal spanning tree port.
A.CEF， distributed CEF （dCEF）， fast switching， process switching
B.distributed CEF （dCEF）， CEF， fast switching， process switching
C.fast switching， process switching， distributed CEF （dCEF）， CEF
D.process switching， fast switching， distributed CEF （dCEF）， CEF
E.process switching， distributed CEF （dCEF）， CEF， fast switching
F.process switching， CEF， distributed CEF （dCEF）， fast switching
最新試題
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）