Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A.
What will happen as a result of this change？（）
A.All ports of the root switch SW_A will remain in forwarding mode throughout the reconvergence of the spanning tree domain.
B.Switch SW_A will change its spanning tree priority to become root for VLAN 2 only.
C.Switch SW_A will remain root for the default VLAN and will become root for VLAN 2.
D.No other switch in the network will be able to become root as long as switch SW_A is up and running.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1.
What will be the result？（）
A.The command will be rejected by the switch.
B.Interfaces FastEthernet0/13 and FastEthernet0/14 will no longer be bundled.
C.Dynamic Trunking Protocol will be turned off on interfaces FastEthernet0/13 and FastEthernet0/14.
D.Interfaces FastEthernet0/13 and FastEthernet0/14 will only allow traffic from the native VLAN.
E.Interfaces FastEthernet0/13 and FastEthernet0/14 will continue to pass traffic for VLANs 88，100，360.
Refer to the exhibit.
What will happen when one more user is connected to interface FastEthernet 5/1？ （）
A.All secure addresses will age out and be removed from the secure address list. This will cause the security violation counter to increment.
B.The first address learned on the port will be removed from the secure address list and be replaced with the new address.
C.The interface will be placed into the error-disabled state immediately， and an SNMP trap notification will be sent.
D.The packets with the new source addresses will be dropped until a sufficient number of secure MAC addresses are removed from the secure address list.
Refer to the exhibit. LACP has been configured on Switch1 as shown.
Which is the correct command set to configure LACP on Switch2？（）
A.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode auto
B.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode passive
C.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode desirable
D.Switch2# configure terminal Switch2（config）# interface range gigabitethernet3/1 -2 Switch2（config-if）# channel-group 5 mode on
Refer to the exhibit.
What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
A.ip routing
B.no ip routing
C.router eigrp 1
D.no router eigrp 1
E.mls qos
F.no mls qos
A.VLAN instance mapping and revision number
B.VLAN instance mapping and member list
C.VLAN instance mapping， revision number， and member list
D.VLAN instance mapping， revision number， member list， and timers
最新試題
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
Refer to the exhibit. Which statement is true about the output？（）