The following output, taken from a show ip bgp command on Router R1, lists two neighbors. In what BGP neighbor state is neighbor 1.1.1.1?()
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down
State/PfxRcd
1.1.1.1 4 1 60 61 26 0 0 00:45:01
0
2.2.2.2 4 3 153 159 26 0 0 00:38:13
1
A. Idle
B. Opensent
C. Active
D. Established
您可能感興趣的試卷
你可能感興趣的試題
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively.
Which of the following commands would not be part of a working eBGP confi guration on Router R1?()
A. router bgp 1
B. neighbor 2.2.2.2 remote- as 2
C. neighbor 2.2.2.2 update - source loopback1
D. neighbor 2.2.2.2 multihop 2
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link.
Which of the following commands would be needed on R1 to configure eBGP?()
A. router bgp 2
B. router bgp 1
C. neighbor 10.1 .1.2 remote - as 2
D. neighbor 10.1.1.2 Update - source 10.1.1.1
E. neighbor 10.1.1.2 Update- source S0/0
A. Single Homed
B. Dual Homed
C. Single Multihomed
D. Dual Multihomed
A. To influence the choice of best path (best route) for at least some routes
B. To avoid having to configure static routes
C. To allow redistribution of BGP routes into the IGP routing protocol
D. To monitor the size of the Internet BGP table
A. The eBGP peer neighborship uses TCP
B. The eBGP peer uses port 180 (default)
C. The eBGP peer uses the same ASN as the local router
D. The eBGP peer updates its AS_Path PA before sending updates to this router
最新試題
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?()
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?()
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?()
Which of the following features work the same in both RIP- 2 and RIPng?()
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?()
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?()
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?()interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()