多項選擇題

Look at the following configuration below and select the statements that are true.()
RD2(config)#router ospf 100
RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - me
RD2(config -router)#!
RD2(config - router) #ip access - list standard match - me
RD2(config - std - nacl)# permit host 172.16.0.0

A. OSPF will have an AD of 180 for routes from 10.1.10.1 in the 172.16.0.0/16 range.
B. The neighbor RID is 10.1.10.1
C. OSPF will have an AD of 180 for all routes.
D. The  local RID is 10.1.10.1


您可能感興趣的試卷

你可能感興趣的試題

3.單項選擇題

Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.
Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?()

A. When the packet received on the LAN interface is permitted by the ACL listed on the tunnel greacl command under the incoming interface
B. When routing the packet, matching a route whose outgoing interface is the GRE tunnel interface
C. When routing the packet, matching a route whose outgoing interface is the IPsec tunnel interface
D. When permitted by an ACL that was referenced in the associated crypto map

最新試題

Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()

題型:單項選擇題

An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?()

題型:單項選擇題

Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64

題型:單項選擇題

Router R1 lists the following output from a show command. Which of the following is true about R1?()R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456

題型:單項選擇題

Which of the following must match for  two directly connected routers running OSPF to establish a neighbor adjacency?()

題型:多項選擇題

Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()

題型:單項選擇題

Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?()

題型:單項選擇題

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?()ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1

題型:單項選擇題

Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0

題型:單項選擇題

Which of the following  answers lists a multicast IPv6 address?()

題型:單項選擇題