On a cisco aironet 802.11 a/b/g wireless lan client adapter， the status led and activity led are alternating on and off.
What does this indicate？（）
A.the client card is not associated to the network.
B.the client card has awakened from power-save mode.
C.the driver has been installed incorrectly.
D.the client card has failed.
您可能感興趣的試卷
你可能感興趣的試題
You have very few cisco 7920 wireless ip phones on your network， but lots of wireless laptops. You want to increase the bandwidth available for the laptops by decreasing the bandwidth
reserved for the cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidth you can select on the wlan controller？（）
A.55 percent
B.75 percent
C.40 percent
D.25 percent
A.windows 2000 sp4
B.windows server 2003
C.solaris 10
D.vista
E.windows xp pro
Your customer has deployed a cisco wireless location appliance within its warehouse
environment. however， employees there have been experiencing problems when tracking objects using active rfid tags. you use an access point scan to determine if the location appliance has been deployed correctly.
Making which change to warehouse deployment location services will most likely correct the problem？（）
A.ensure channels are deployed such that they do not overlap
B.allow for the automatic containment of rogue access points
C.ensure each area is covered by a minimum of three access points
D.ensure a minimum rssi value of -50
A.4
B.32
C.8
D.16
A cisco 4404 wlan controller is being connected to a cisco 6500 catalyst series switch.
How would you interconnect and configure lag for connectivity and ensure redundancy？（）
A.all four ports from the cisco wlc terminated to the same catalyst gigabit module and channel group.
B.ports 1 and 2 from cisco wlc to catalyst gigabit module slot 1 channel group 10 and cisco wlc ports 3 and 4 to catalyst gigabit module slot 2 channel group 10.
C.all four ports from the cisco wlc terminated to the same catalyst gigabit module using two channel groups.
D.ports 1 and 2 from cisco wlc to catalyst gigabit module slot 1 channel group 20 and cisco wlc ports 3 and 4 to catalyst gigabit module slot 2 channel group 40.
最新試題
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）