You are troubleshooting a problem with a cisco 7920 wireless ip phone on a standalone wlan. the phone rings but， when you Answer ，the call is dropped.
What may have caused this problem？（）
A.publicly secure packet forwarding is enabled.
B.the minimum data rate is not set to 11 mbps.
C.an address resolution protocol is enabled.
D.the access point is set to the least congested channel.
您可能感興趣的試卷
你可能感興趣的試題
A cisco wcs version 4.0 has been installed on a server with a dual pentium 3.0 ghz processor，4 gb ram，and an 80 gb hard drive. a location appliance has been incorporated into the network and is being monitored by the cisco wcs. there are 3000 devices to be tracked but not all of them are being tracked on the cisco wcs.
What can be done to correct the problem？（）
A.add a new location appliance.
B.add a new cisco wcs server dedicated to the location appliance.
C.add 4 gb of ram to the cisco wcs.
D.add a 120 gb hard drive to the cisco wcs.
You are troubleshooting a problem with a cisco 7920 wireless ip phone that is causing the phone to drop calls. the problem appears to be a roaming bandwidth issuE. in order to verify what kind of issue it is， you decide to increase the bandwidth reserved for roaming on the wlan controller to the maximum.
What level do you set the bandwidth to？（）
A.25 percent
B.15 percent
C.5 percent
D.35 percent
Using the wlse， you are trying to push out a configuration job to a standalone access point， but the job does not start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect snmp communities on the access point
C.pop-up blocker enabled in the browser
D.unsupported version of ios firmware in the access point
A.1000
B.1500
C.2000
D.2500
A.16 feet [4.8 meters]
B.24 feet [7.3 meters]
C.8 feet [2.4 meters]
D.40 feet [12.1 meters]
最新試題
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.Which situation would result in thistype of problem？（）