A.15
B.10
C.1
D.5
您可能感興趣的試卷
你可能感興趣的試題
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A clientthat is anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment of the tunnel from the foreign controller’sperspective？（）
A.Received Mobile Anchor Export message
B.Transmit Plumbing duplex mobility tunnel message
C.Received Plumbing duplex mobility tunnel message
D.Transmit Mobile Anchor Export message
You are charged with implementing a secure wireless installation which will provide Internet
access to client devices but will not allow communications between wireless clients. In addition toimplementing PSPF or peer-to-peer blocking on the wireless side.
Which of the following actionsshould you perform on the wired infrastructure？（）
A.Implement a Cisco Secure IPS sensor.
B.Implement 802.1X on the switch ports.
C.Take no action， you have achieved your goal.
D.Implement a protected port on the access switches.
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.
Which two IETF RADIUS attributes should you configure on the Cisco SecureACS？（）
A.083 Tunnel-Preference
B.066 Tunnel-Client-Endpoint
C.064 Tunnel-Type
D.082 Tunnel-Assignment-ID
E.081 Tunnel-Private-Group-ID
F.067 Tunnel-Server-Endpoint
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue andblinking，but the status LED and Ethernet LED are both off.
What does this indicate（）？
A.A firmware upgrade is in progress.
B.An access point buffer overflow is occurring.
C.The access point is booting.
D.The internal radio has failed.
A.router（config-ssid）# enable
B.router（config-ssid）# advertise
C.router（config-ssid）# broadcast
D.router（config-ssid）# guest-mode
最新試題
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）