A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it，which continue to pass traffic.
What has causedthis problem？（）
A.H-REAP AP1 has reached its client limit.
B.H-REAP AP2 has reached its client limit.
C.H-REAP AP2 lost its connection to the controller.
D.H-REAP AP1 lost its connection to the controller.
您可能感興趣的試卷
你可能感興趣的試題
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied.
What is wrong？（）
A.Polling values can be changed only in the maintenance window.
B.Polling values can be changed only on the location server.
C.Your login does not have the correct permissions.
D.You must wait for the location server to become available.
On a Cisco 1000 Series controller-based access point， the alarm LED is flashing red， but the otherLEDs are off.
What is this access point indicating？（）
A.Its IP address already exists.
B.It is operating normally.
C.It requires a code upgrade.
D.It has lost contact with the controller.
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network， but clients using PEAP are failing to log on.
Which situation would result in thistype ofproblem？（）
A.Posture validation has not been enabled
B.The AAA server is set to accept both MS-CHAP v2 and GTC for PEAP authentication
C.Clients and server are not using certificates
D.Clients have been set to validate the server identity
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter， the status LED and activity LED arealternating on and off.
What does this indicate？（）
A.The client card is not associated to the network.
B.The client card has awakened from power-save mode.
C.The driver has been installed incorrectly.
D.The client card has failed.
You have very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops. Youwant to increase the bandwidth available for the laptops by decreasing the bandwidth reserved forthe Cisco 7920 phones.
What is the lowest percentage of voice-allocated bandwidth you can select onthe WLAN controller？（）
A.55 percent
B.75 percent
C.40 percent
D.25 percent
最新試題
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
How many WLANs can a Cisco Aironet 1242 in H-REAP mode support when actively connected toa wireless controller？（）
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）