In a deployment using standalone access points， clients set up to authenticate with EAP-PEAP orEAP-Cisco Wireless （Cisco-LEAP） cannot authenticate. When you inspect the Failed Attempts reporton the Cisco Secure ACS， you find this error： "Unknown network access server NAS."
Which problem may have caused this failure？（）
A.misconfigured IP address of the AAA server on the access point
B.misconfigured EAP type on the access point
C.misconfigured IP address of the access point on the AAA server
D.misconfigured EAP type on the AAA server
您可能感興趣的試卷
你可能感興趣的試題
A.router （config-ssid）# guest-mode
B.router （config-ssid）# advertise
C.router （config-ssid）# enable
D.router （config-ssid）# broadcast
Your customer has deployed a Cisco Wireless Location Appliance within its warehouseenvironment.
However， employees there have been experiencing problems when tracking objects using activeRFID tags.The RFID tag data is not being collected.
On which device would you verify that RFIDs have been enabled？（）
A.access point
B.location manager
C.wireless controller
D.Cisco WCS
A.partners having a discussion with customers about the minimum service components needed to successfully deploy a wireless solution
B.customers determining a competitor’s strategy for adopting advanced technologies
C.partners choosing the right products for their customers
D.customers choosing the right products for their network
E.customers defining the correct strategy for advanced technology adoption
You are using standalone Cisco Aironet 1400 Series Wireless Bridges for a nine-mile point-to-pointwireless link between two buildings.
Which distance setting should you use for the bridgeconfigured as theroot？（）
A.20 km [12.4 miles]
B.10 km [6.2 miles]
C.5 km [3.1 miles]
D.25 km [15.5 miles]
E.15 km [9.3 miles]
EAP-FAST provides a secure tunnel during Phase One to protect the user’s authentication credentials.
Which of these entities initializes the secure tunnel？（）
A.x.509 certificate
B.generic token card
C.preshared key
D.Protected Access Credential
最新試題
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
Static WEP is configured on the access point. You are authenticated and associated to the accesspoint but are unable to obtain an IP address.Which of the following will cause this problem？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
The IOS of a North American Cisco Aironet 1130AG Series standalone access point has becomecorrupt. You must therefore reload the TFTP firmware.Before you press and hold the MODEbutton， you should verify that the file name is which of the following？（）
An REAP was supporting 16 WLANs， but now it only supports one.What happened to cause the change？（）
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue and blinking，but the status LED and Ethernet LED are both off.What does this indicate？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）