On a Cisco Aironet 1130 Series autonomous access point， the status indicator is blinking dark blue.
What does this indicate？（）
A.The access point is booting.
B.A firmware upgrade is in progress.
C.The internal radio has failed.
D.An access point buffer overflow is occurring.
您可能感興趣的試卷
你可能感興趣的試題
A.rogue detector
B.rogue containment
C.RLDP
D.RIDP
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The
phone rings but， when you answer， the call is dropped.
What may have caused this problem？（）
A.Publicly Secure Packet forwarding is enabled.
B.The minimum data rate is not set to 11 Mbps.
C.An address resolution protocol is enabled.
D.The access point is set to the least congested channel.
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor， 4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the network and isbeing monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of them are beingtracked on the Cisco WCS.
What can be done to correct the problem？（）
A.Add a new location appliance.
B.Add a new Cisco WCS server dedicated to the location appliance.
C.Add 4 GB of RAM to the Cisco WCS.
D.Add a 120 GB hard drive to the Cisco WCS.
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be a roaming bandwidth issue. In order to verify what kindof issue it is， you decide to increase the bandwidth reserved for roaming on the WLAN controllerto the maximum.
What level do you set the bandwidth to？（）
A.25 percent
B.15 percent
C.5 percent
D.35 percent
Using the WLSE， you are trying to push out a configuration job to a standalone access point， butthe job does not start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.incorrect SNMP communities on the access point
C.pop-up blocker enabled in the browser
D.unsupported version of IOS firmware in the access point
最新試題
You are installing a Cisco 4402 Series Wireless LAN Controller.What type of interface is used on the uplink port？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones，which two general control settings should you select？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem？（）