A. All "Add" channels require uniform power levels.
B. The flexibility of wavelengths per OADM is limited.
C. It is easier to balance "Pass-Through" and "Add" channels.
D. There is lower pass-through loss using multi-channel OADMs.
E. You can extract a single channel without dropping other channels.
您可能感興趣的試卷
你可能感興趣的試題
Click the Exhibit button. Given the following parameters: transmitter output (min): -2 dBm receiver input (min): -28 dBm 15216 Mux and Demux loss: 4.5 dB 16 channels maximum In which sites shown in the exhibit could the 15216 EDFAs be placed to minimize the number of EDFAs needed?（）
A. Locations B, C only
B. Locations A, B, C only
C. Locations A, B, D only
D. Locations B, C, D only
E. Locations A, B, C, D
A. The ONS 15216 OADM can be provisioned to add/drop one, two, or four channels via Cisco Transport Manager (CTM).
B. The ONS 15216 OADM consists only of a four-channel module, and the number of ports utilized determines whether it is a one, two, or four channel OADM.
C. Three separate OADM modules are available for one, two, and four channels. The wavelengths to be dropped and added are programmable via Cisco Transport Manager (CTM).
D. The ONS 15216 OADM consists only of a single-channel module. Two-channel and four-channel support is available by stacking the single-channel module.
E. The ONS 15216 OADM is available in one, two, four channels. There are 32 single-channel OADM modules, 16 two-channel OADM modules, and 8 four-channel OADM modules.
Click the Exhibit button. The exhibit shows a 15454/15216 DWDM system and alarm indications. What are two possible sources of trouble shown in the system?（） (Choose two.)
A. fiber failure between Sites A and d
B. EDFA failure at Site A (clockwise direction)
C. EDFA failure at Site C (clockwise direction)
D. 15216 multiplexer at Site A (counter-clockwise direction)
E. OADM pass-through (West "OUT") failure at site D (clockwise)
F. wavelengths 1 and 3 transmitter failures at Site A (clockwise direction)
A. dispersion
B. Optical SNR
C. span attenuation
D. four wave mixing
E. receiver sensitivity
A. the K1 SONET byte； the K2 SONET byte
B. the K2 SONET byte；the K1 SONET byte
C. transmitter switching；receiver detection
D. Line Overhead bytes；Path Overhead bytes
E. Path Overhead bytes；Line Overhead bytes
最新試題
Why are the 1300 nm and 1550 nm regions of the fiber spectrum primarily used for optical communications?（）
Which timing mode is appropriate for a SONET NE that is adjacent to a SONET NE using BITS-1 timing source?（）
Click the Exhibit button. Which type of multiplexer is shown in the exhibit?（）
If node 2 is accepting line timing from node 1, node 2 will send （）to node 1 as its SSM message.
Given the formula: (Fiber Attenuation * Km) + (Splice Attenuation * # of Splices) + (Connector Attenuation * # of Connectors) + (Optical Fiber or OADM) + Buffer(Fiber aging)) With regard to SONET/SDH optical calculations, what will the given formula provide?（）
Which is a legitimate bandwidth matched pair?（）
If the power is 0 dBm, what is the power in mW?（）
The dispersion of a non-zero dispersion shifted fiber is 6 ps/nm*km at 1550 nm and 10 ps/nm*km at 1610 nm. What is the minimum dispersion compensation required if an L-Band DWDM signal travels through 200 km of fiber and has a dispersion tolerance of 1800 ps/nm?（）
Click the Exhibit button. When designing a DWDM system with multiple amplified spans, a pre-amp is needed at Site B to （）. (Choose three.)
What is an advantage of an externally modulated laser over a directly modulated laser?（）