Refer to the exhibit.After a RIP route is marked invalid on Router_1, how much time will elapse before that route is removed from the routing table?()
A.30 seconds
B.60 seconds
C.90 seconds
D.180 seconds
E.240 seconds
您可能感興趣的試卷
你可能感興趣的試題
A.proxy
B.dual-stack
C.tunneling
D.dot1q
A.user EXEC mode
B.global configuration mode
C.privileged EXEC mode
D.auxiliary setup mode
A.Router(config)#router ospf 1
B.Router(config)#router ospf 0
C.Router(config)#router ospf area 0
D.Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
E.Router(config-router)#network 192.168.16.0 0.0.0.255 0
F.Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
Refer to the exhibit.S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology. While testing this configuration, a technician notes that pings are successfully from hosts on the 172.16.1.0/24 network to hosts on both the 172.16.2.0/25 and 172.16.0.2.128/25 networks. However, pings between hosts on the 172.16.2.0/25 and 172.16.2.128/25 network are not successful. What could explain this connectivity problem?()
A.The ip subnet-zero command has been issued on the R1 router.
B.The RIPv2 dynamic routing protocol cannot be used across a Frame Relay network.
C.Split horizon is preventing R2 from learning about the R3 networks and R3 from learning about R2 networks.
D.The 172.16.2.0/25 and 172.16.2.128/25 networks are overlapping networks that can be seen by R1,but not between R2 and R3.
E.The 172.16.3.0/29 network used on the Frame Relay links is creating a discontiguous network between the R2 and R3 router subnetworks.
A.when a packet is received from an 802.1Q trunk,the vlan id can be determined from the source MAC address table
B.unkown unicast frames are retransmitted only to the ports that belong to the same vlan
C.ports between switches should be configured in access mode so that vlans can span across the ports
D.broadcast and multicast frames are retransmitted to ports that are configured on different vlan.
最新試題
請參見圖示。某用戶想要查看當前的配置。圖中所示為ipconfig/all 命令的輸出。從此輸出可以得到哪三項結論?()
請參見圖示。網絡技術人員使用圖中所示的連接將主機A 連接到路由器以創建初始配置。下列有關此連接的陳述中哪一項正確?()
以下哪兩種介質可提供高達1Gb/s 的帶寬?()
PC 無法連接到任何遠程網站,無法ping 通其默認網關,也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常?()
在Cisco IOS 設備中,啟動配置文件存儲于何處?()
在路由器上使用Router#copy running-config startup-config 命令會產生什么效果?()
請參見圖示。圖中所示路由表所屬的PC 已正確配置。IP 地址192.168.1.254屬于哪一個網絡設備或接口?()
請參見圖示。網絡中的主機A 正在向主機B 發送數據段。有關所交換的數據段的流量控制如圖所示。下列關于此通信的陳述,哪兩項是正確的?()
請參見圖示。已啟用路由器的NAT 功能供PC 訪問Internet??梢詾槁酚善鹘涌赟0/0/0分配下列哪一個IP 地址?()
請參見圖示。主機B 嘗試與主機C 建立TCP/IP 會話。在嘗試期間,San Francisco 器由器的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為10.10.1.2而目的IP 地址為10.31.1.20的數據包。捕獲該幀時,它的目的MAC 地址是什么?()