Refer to the exhibit.Give this output for SwitchC， what should the network administrator’s next action be？（）
A.Check the trunk encapsulation mode for SwitchC’s fa0/1 port.
B.Check the duplex mode for SwitchC’s fa0/1 port.
C.Check the duplex mode for SwitchA’s fa0/2 port.
D.Check the trunk encapsulation mode for SwitchA’s fa0/2 port.
您可能感興趣的試卷
你可能感興趣的試題
A.NCP
B.LCP
C.ISDN
D.DLCI
E.SLIP
What can be determined from the line of show ip route output shown in the exhibit？（）
A. The next routing update can be expected in 35 seconds.
B. The IP address 10.10.10.6 is configured on S0/1.
C. The IP address 10.10.10.8 is configured on S0/1.
D. This route is using the default administrative distance.
E. The 10.10.10.8 network is two hops away from this router.
A.Microsegmentation decreases the number of collisions on the network.
B.if a switch receives a frame for an unkown destination,it uses ARP to resolve the address.
C.Spanning Tree Protocol allows switches to automatically share vlan information.
D.In a properly functioning network with redundant switched paths,each switched aegment will contain one root bridge with all its ports in the forwarding state.All other switches in that broadcast domain will have only one root port.
E.Establishing vlans increases the number of broadcast domains.
F.Switches that are configured with vlans make forwarding decisions based on both layer 2 and layer 3 address information.
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally， static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes？（）
A.Configure the no ip subnet-zero command on R1,R2,and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
Which destination addresses will be used by Host A to send data to Host C？（）
A. the IP address of Switch 1
B. the MAC address of Switch 1
C. the IP address of Host C
D. the MAC address of Host C
E. the IP address of the router’s E0 interface
F. the MAC address of the router’s E0 interface
最新試題
傳輸層如何讓主機能同時針對不同應用程序維護多個通信流？（）
下列哪些是私有IP 地址的地址范圍？（）
PC 無法連接到任何遠程網站，無法ping 通其默認網關，也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常？（）
請參見圖示。公司路由器由于故障被更換。更換路由器之后，Education 辦公室內的主機C 和D 能夠相互ping 通，但是無法訪問Accounts 辦公室內的主機。此問題的原因可能是什么？（）
要將數據包發送到遠程網絡，應使用哪種設備？（）
OSI 哪一層可提供有序的數據重構服務？（）
請參見圖示。主機B 嘗試與主機C 建立TCP/IP 會話。在嘗試期間，San Francisco 器由器的FastEthernet 接口fa0/1捕獲到一個幀。捕獲的幀中包含源IP 地址為10.10.1.2而目的IP 地址為10.31.1.20的數據包。捕獲該幀時，它的目的MAC 地址是什么？（）
請參見圖示。一臺路由器（其路由表如圖所示）收到發往192.168.1.4的數據包。路由器將如何處理該數據包？（）
請參見圖示。當計算機A 向計算機D 發送幀時，哪些計算機會接收該幀？（）
在Cisco IOS 設備中，啟動配置文件存儲于何處？（）