Refer to the exhibit.
What will happen when one more user is connected to interface FastEthernet 5/1？（）
A. The first address learned on the port will be removed from the secure address list and be replaced with the new address.
B. All secure addresses will age out and be removed from the secure address list. This will cause the security violation counter to increment.
C. The packets with the new source addresses will be dropped until a sufficient number of secure MAC addresses are removed from the secure address list.
D. The interface will be placed into the error-disabled state immediately， and an SNMP trap notification will be sent.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. The show port-security interface fa0/1 command was issued on switch SW1. Given the output that was generated，
which two security statement are true？ （）
A. Interface FastEthernet 0/1 was configured with the switchport port-security aging command.
B. Interface FastEthernet 0/1 was configured with the switchport port-security protect command.
C. Interface FastEthernet 0/1 was configured with the switchport port-security violation restrict command.
D. When the number of secure IP addresses reaches 10， the interface will immediately shut down.
E. When the number of secure MAC addresses reaches 10， the interface will immediately shut down and an SNMP trap notification will be sent.
Switch R1 has been configured with Private VLANs.
With that type of PVLAN port should the default gateway be configured？（）
A. Trunk
B. Isolated
C. Primary
D. Community
E. Promiscuous
F. None of the other alternatives apply
What is true about access control on bridged and routed VLAN traffic？ （）
A. Router ACLs can be applied to the input and output directions of a VLAN interface.
B. Bridged ACLs can be applied to the input and output directions of a VLAN interface.
C. Only router ACLs can be applied to a VLAN interface.
D. VLAN maps and router ACLs can be used in combination.
E. VLAN maps can be applied to a VLAN interface
On a Company switch named R1 you configure the following： iparp inspection vlan 10-12， 15
What is the purpose of this global configuration command made on R1？（）
A. Discards ARP packets with invalid IP-to-MAC address bindings on trusted ports
B. Validates outgoing ARP requests for interfaces configured on VLAN 10， 11， 12， or 15
C. Intercepts， logs， and discards ARP packets with invalid IP-to-MAC address bindings
D. Intercepts all ARP requests and responses on trusted ports
E. None of the other alternatives apply
As the network technician at Company， you need to configure DHCP snooping on a new switch.
Which three steps are required？ （）
A. Configure the switch to insert and remove DHCP relay information （option-82 field） in forwarded DHCP request messages.
B. Configure DHCP snooping globally.
C. Configure the switch as a DHCP server.
D. Configure DHCP snooping on an interface.
E. Configure all interfaces as DHCP snooping trusted interfaces.
F. Configure DHCP snooping on a VLAN or range of VLANs.
最新試題
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
What two things will occur when an edge port receives a BPDU？（）
Which three statements about STP timers are true？（）
Refer to the exhibit. Which statement is true about the output？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）