The Company network needs to pass traffic between VLANs.
Which device should be used to accomplish this？ （）
A. Hub
B. Switch
C. Router
D. Bridge
E. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
pany has implemented numerous multilayer switches that utilize FIB tables.
Which statement is true about the Forward Information Base （FIB） table？（）
A. The FIB is derived from the IP routing table and is optimized for maximum lookup throughput.
B. The FIB table is derived from the Address Resolution Protocol table， and it contains Layer 2 rewrite （MAC） information for the next hop.
C. When the FIB table is full， a wildcard entry redirects traffic to the Layer 3 engine.
D. The FIB lookup is based on the Layer 2 destination MAC address.
E. None of the other alternatives apply
Refer to the exhibit.
What type of attack is being defended against？ （）
A. snooping attack
B. rogue device attack
C. STP attack
D. VLAN attack
E. spoofing attack
F. MAC flooding attack
Refer to the exhibit.
What will happen to traffic within VLAN 14 with a source address of 172.16.10.5？（）
A. The traffic will be forwarded to the router processor for further processing.
B. The traffic will be dropped.
C. The traffic will be forwarded to the TCAM for further processing.
D. The traffic will be forwarded without further processing.
Refer to the exhibit.
What will happen when one more user is connected to interface FastEthernet 5/1？（）
A. The first address learned on the port will be removed from the secure address list and be replaced with the new address.
B. All secure addresses will age out and be removed from the secure address list. This will cause the security violation counter to increment.
C. The packets with the new source addresses will be dropped until a sufficient number of secure MAC addresses are removed from the secure address list.
D. The interface will be placed into the error-disabled state immediately， and an SNMP trap notification will be sent.
Refer to the exhibit. The show port-security interface fa0/1 command was issued on switch SW1. Given the output that was generated，
which two security statement are true？ （）
A. Interface FastEthernet 0/1 was configured with the switchport port-security aging command.
B. Interface FastEthernet 0/1 was configured with the switchport port-security protect command.
C. Interface FastEthernet 0/1 was configured with the switchport port-security violation restrict command.
D. When the number of secure IP addresses reaches 10， the interface will immediately shut down.
E. When the number of secure MAC addresses reaches 10， the interface will immediately shut down and an SNMP trap notification will be sent.
最新試題
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. On the basis of the output of the show spanning-tree inconsistentports command， which statement about interfaces FastEthernet 0/1 and FastEthernet 0/2 is true？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. Which statement is true about the output？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Refer to the exhibit. For what purpose is the command show ip cef used？（）