A. The IBGP neighbor is not directly connected.
B. BGP synchronization is enabled in a transit autonomous system with fully - meshed IBGP neighbors.
C. The EBGP neighbor ebgp - multihop option is set to the de fault value.
D. The BGP update interval is different between the two BGP neighbors.
E. The BGP neighbor is referencing an incorrect autonomous system number in its neighbor statement.
F. There is an access list blocking all TCP traffic between the two BGP neighbors.
您可能感興趣的試卷
你可能感興趣的試題
A. show ip bgp paths
B. show ip bgp peers
C. show ip bgp
D. show ip bgp summary
A. local preference
B. MED
C. weight
D. or igin
E. next - hop
F. AS - path
A. using aggregate routes
B. defining routes via the network statement
C. disablin g synchronization
D. forcing the next - hop address
Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? （）
A. Router A will prefer the path through router B for network 172.20.0.0
B. Router A will prefer the path through router C for network 172.20.0.0
C. Packets from router D will prefer the path through router B for networks advertised by router A
D. Packets from r outer D will prefer the path through router C for networks advertised by router A
A. Advertise with a high MED value all networks that are discovered via external BGP.
B. Set the no - export community attribute on all networks that are advertised externally.
C. Remove the AS - Path information on all routes in the BGP table pr ior to advertising externally.
D. Set the origin code to incomplete for all networks that are discovered via external BGP.
E. Only advertise networks externally if they have been discovered via internal BGP.
F. Use an outgoing distribution list to filte r all networks not originating from inside the autonomous system.
最新試題
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）