Refer to the exhibit. Based on the output from the show command on RT1which statement is true? （）
A. OSPFv3 uses global IPv6 addresses to establish neighbor adjacencies.
B. RT1 has a subnet mask of 64 bits .
C. RT1 has FastEthernet0/0 set as a DR for network type broadcast.
D. OSPFv3 uses Link - local addresses to establish neighbor adjacencies.
E. RT1does not have a global IPv6 address set on FastEthernet0/0.
F. OSPFv3 uses IPv4 addresses to establish nei ghbor adjacencies.
您可能感興趣的試卷
你可能感興趣的試題
A. It must be issued before the network command to enable the OSPF pr ocess for IPv6.
B. It must be issued after the network command to enable the OSPF process for IPv6.
C. It must be issued in router global configuration mode to enable the OSPF process for IPv6.
D. It must be issued in interface configuration mode to ena ble the OSPF process for IPv6.
In IPv6, the interfaces running OSPF can be configured with multiple ad dress prefixes.
Which statement is true about the IPv6 addresses that can be included into the OSPF process?" （）
A. Specific addresses can be selected using a prefix list.
B. Specific addresses can be selected using a route map.
C. Specific addresses cann ot be selected for importation into the OSPF process.
D. Specific addresses can be selected using an ACL.
A. The shortest path first (SPF) algorithm is performed on the LSA database.
B. The OSPF adjacencies are cleared and initiated again.
C. The OSPF database is repopulated. Then the shortest path first (SPF) algorithm is performed.
D. The route table is cleared. Then the OSPF neighbors are reformed.
A. all routers in a local segment
B. all routers in an autonomous system
C. all hosts in a local segment
D. all hosts in a particular multicast group
A. If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.
B. A router does not have to be a member of a multicast group to receive multicast data.
C. A router must be a member of a multicast group to send to the group.
D. A router does not have to be a member of a multicast group to send to the group.
E. If a packet is sent to a multicast group address, all members of the multicast group will rece ive it.
F. A router must be a member of a multicast group to receive multicast data.
最新試題
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Which of the following are true of both OSPFv2 and OSPFv3?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）