多項選擇題Which three of the following network features are methods used to achieve high availability? ()

A. Spanning Tree Protocol (STP)
B. Delay reduction
C. Hot Standby Routing Protocol (HSRP)
D. Dynamic routing protocols
E. Quality of Service (QoS)
F. Jitter management


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題

What can be determined about the HSRP relationship from the displayed debug output? ()

A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router  172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router  172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.

2.多項選擇題

Examine the router output above. 
Which two items are correct? ()

A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown, the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up, the priority will become 105.
E. Router A will assume the active state if its priority is the highest.

3.多項選擇題

Refer to the exhibit. Based upon the debug output that is shown, 
which three statements about  HSRP are true?()

A. The router with IP address 172.16.11.111 haspreempt configured.  
B. The final active router is the router with IP address 172.16.11.111.
C. The router with IP address 172.16.11.112 has nonpreempt configured.
D. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP  address 172.16.11.111.
E. The router with IP address 172.16.11.112 is using default HSRP priority.
F. The IP address 172.16.11.115 is the virtual HSRP IP address.

4.多項選擇題

Refer to the exhibit. 
Which two problems are the most likely cause of the exhibited output?()

A. transport layer issues
B. VRRP misconfiguration
C. HSRP misconfiguration
D. physical layer issues
E. spanning tree issues

5.多項選擇題

Examine the router output above. Which two items are correct?()

A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown, the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up, the priority will become 105.
E. Router A will assume the active state if its priority is the highest.

最新試題

Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result?()

題型:單項選擇題

Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain, the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change?()

題型:單項選擇題

How are STP timers and state transitions affected when a topology change occurs in an STP environment?()

題型:單項選擇題

Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network, Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit, which two statements are true?()

題型:多項選擇題

During routine maintenance, it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time, DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ? ()

題型:單項選擇題

Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2?()

題型:單項選擇題

Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2?()

題型:單項選擇題

Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result?()

題型:單項選擇題

DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ? ()

題型:單項選擇題

Refer to the exhibit. For what purpose is the command show ip cef used?()

題型:單項選擇題