A. Only the path that is the feasible successor should be used.
B. Load balancing is disabled on t his router.
C. The router only performs equal - cost load balancing on all paths that have a metric greater than 1
D. The router performs equal - cost load balancing.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. On the basis of the partial configuration, which two statements are correct? ()
A. Only routes 10.0.1.0/24 will be sent out all interfaces.
B. Only routes matching 10.0.0.0/8 will be advertised out interfaces other than Ethernet 0.
C. Only routes matching 10.0.0.0/8 will be advertised out Ethernet 0.
D. Only routes matching 10.0.1.0/24 will be advertised out Ethernet 0.
E. Only routes 10.0.1.0/24 will be allowed in the routing table.
F. All rout es will be advertised out interfaces other than Ethernet 0.
A. many - to - one
B. one - to - one
C. one - to - many
D. many - to - many
A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface
B. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interface
C. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface
D. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interface
E. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface
F. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?()
A. Issue the command bandwidth 224 on the physical interface.
B. Issue the command bandwidth 56 on the physical interface.
C. Issue the command bandwidth 224 on each subinterface.
D. Issue the command bandwidth 56 on each subinterface.
Which statement is correct based upon the following output from the show command on RT1 ? ()
A. OSPFv3 establishes neighbor adjacencies by using global IPv6 addresses.
B. OSPFv3 establishes neighbor adjacencies by using Link - local addresses.
C. RT1 owns a subnet mask of 64 bits.
D. OSPFv3 establishes neighbor adjacencies by using IPv4 addr esses.
最新試題
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?()interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?()
A client host uses IPv4 to communicate with one ser ver and IPv6 to communicate with another.Which of the following IPv6 coexistence features is likely at work on the host?()
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?()
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?()
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?()
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?()interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Look at the following configuration below and select the statements that are true.()RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?()ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable