A. L1 ES
B. L2 IS
C. L2 ES
D. L1 IS
E. L1/L2 IS
您可能感興趣的試卷
你可能感興趣的試題
A. IS - IS is more CPU - intensive than is OSPF
B. For greater fine tuning there are more IS - IS timers
C. IS - IS LSP con tains TLV fields and OSPF LSU contains the LSAs
D. New additions to the protocol are easily implemented in OSPF but not with IS - IS
E. OSPF has more area types than does IS - IS
A. uses a default IOS metric of 10 on each interface
B. uses an on - demand circuit to reduce the hello and LSA flooding across switched WAN li nks,such as ISDN
C. uses a DIS and a backup DIS to present the psuedo - node on the LAN
D. encapsulates PDUs directly into a data - link frame
E. uses stubby areas to improve network scalability
F. runs PRC (Partial Route Calculations) to calculate IP re achability information
A. BGP requires redundant TCP sessions between iBGP peers.
B. Routes learned via eBGP are never propagated to other iBGP peers.
C. A full mesh allows for optimal routing within the Transit AS.
D. Routes learned via iBGP are never propagated to other eBGP peers.
E. Routes learned via iBGP are never propagated t o other iBGP peers.
Given the network diagram, which address would successfully summarize only the networks seen? （）
A. 192.168.0.0/24
B . 192.168.8.0/20
C. 192.168.8.0/21
D. 192.168.12.0/20
E. 192.168.16.0/21
F. These networks cannot be summarized.
A. EIGRP
B. RIP
C. OSPF
D. IS - IS
最新試題
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
An engineer is trying to summarize the following networks using the "ip summary- address eigrp"command:10.8.88.0/2510.8.89.48/2910.8.64.96/27Which network and subnet mask below would be the smallest EIGRP summary address to include all three subnets?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）