A. It lists a set of path attributes, along with a list of prefixes that use those PAs
B. It lists a prefix/length, plus the PA settings for that prefix
C. It lists withdrawn routes, but never in the same Update message as newly advertised routes
D. A single Update message lists at most a single prefix/lengtH
您可能感興趣的試卷
你可能感興趣的試題
The following output was taken from the show ip bgp command on Router R2. In this case, which of the following commands are most likely to already be configured on R2?（）
BGP router identifier 11.11.11.11, local AS number 11
...
Neighbor V AS Ms gRcvd MsgSent TblVer InQ OutQ Up/Down
State/PfxRcd
1.1.1.1 4 1 87 87 0 0 0 00:00:06 Idle
(Admin)
2.2.2.2 4 3 173 183 41 0 0 00:58:47
A. router bgp 11
B. neighbor 1.1.1.1 remote- as 11
C. neighbor 2.2.2.2 prefix - limit 1
D. neighbor 1.1.1.1 shutdown
The following output, taken from a show ip bgp command on Router R1, lists two neighbors. In what BGP neighbor state is neighbor 1.1.1.1?（）
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down
State/PfxRcd
1.1.1.1 4 1 60 61 26 0 0 00:45:01
0
2.2.2.2 4 3 153 159 26 0 0 00:38:13
1
A. Idle
B. Opensent
C. Active
D. Established
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively.
Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）
A. router bgp 1
B. neighbor 2.2.2.2 remote- as 2
C. neighbor 2.2.2.2 update - source loopback1
D. neighbor 2.2.2.2 multihop 2
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link.
Which of the following commands would be needed on R1 to configure eBGP?（）
A. router bgp 2
B. router bgp 1
C. neighbor 10.1 .1.2 remote - as 2
D. neighbor 10.1.1.2 Update - source 10.1.1.1
E. neighbor 10.1.1.2 Update- source S0/0
A. Single Homed
B. Dual Homed
C. Single Multihomed
D. Dual Multihomed
最新試題
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?（）
Router R1 lists the following output from a show command. Which of the following is true about R1?（）R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）