Two access points running the core feature set are connected to the same switch and are
providing guest services. if pspf is enabled.
What must be enabled on the switch to prevent clients from seeing one another’s data？（）
A.port-based radius
B.802.1q trunking
C.inline power
D.protected port
您可能感興趣的試卷
你可能感興趣的試題
A.startup
B.site survey mode
C.lost connection to the controller
D.duplicate ip address
Last december you erected a bridge link between two buildings on your campus. it is now april and the foliage in the trees is full， and the bridge link will no longer maintain connectivity.
Which action will most likely solve the problem？（）
A.change the channel selection.
B.install higher gain antennas.
C.raise the antennas.
D.increase transmitter power.
An 802.1x client cannot authenticate to an autonomous access point configured for multiple vlans. the native vlan does not have an ssid configured.
Which one of the following links being down would prevent the clients from authenticating？（）
A.between the radius and the access point
B.between the client’s vlan and the wlse
C.between the native vlan and the wlse
D.between the client’s vlan and the radius
A.1
B.4
C.2
D.5
E.3
In a deployment using the lightweight access points， clients set up to authenticate with eap-peap or eap-cisco wireless （leap） cannot authenticatE. upon inspection of the failed attempts report you see the following error： "unknown network access server nas."
What two problems can cause this type of failure？（）
A.misconfigured ip address of the aaa server on the wireless controller
B.misconfigured ip address of the wireless lan controller on the aaa server
C.misconfigured eap type on the wireless lan controller
D.misconfigured shared secret on the wireless lan controller
E.misconfigured eap type on the aaa server
最新試題
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client thatis anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.Which message would best describe the establishment ofthe tunnel from the foreign controller’s perspective？（）
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.Which two IETF RADIUS attributes should you configure on the CiscoSecure ACS？ （）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You review the Failed Attempts logs on an AAA server and find： "unknown network access servererror." Which failure could produce this error？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）