A.PPP
B.FDDI
C.Frame Relay PVC
D.NBMA
E.Frame Relay SVC
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit.Give this output for SwitchC， what should the network administrator’s next action be？（）
A.Check the trunk encapsulation mode for SwitchC’s fa0/1 port.
B.Check the duplex mode for SwitchC’s fa0/1 port.
C.Check the duplex mode for SwitchA’s fa0/2 port.
D.Check the trunk encapsulation mode for SwitchA’s fa0/2 port.
A.NCP
B.LCP
C.ISDN
D.DLCI
E.SLIP
What can be determined from the line of show ip route output shown in the exhibit？（）
A. The next routing update can be expected in 35 seconds.
B. The IP address 10.10.10.6 is configured on S0/1.
C. The IP address 10.10.10.8 is configured on S0/1.
D. This route is using the default administrative distance.
E. The 10.10.10.8 network is two hops away from this router.
A.Microsegmentation decreases the number of collisions on the network.
B.if a switch receives a frame for an unkown destination,it uses ARP to resolve the address.
C.Spanning Tree Protocol allows switches to automatically share vlan information.
D.In a properly functioning network with redundant switched paths,each switched aegment will contain one root bridge with all its ports in the forwarding state.All other switches in that broadcast domain will have only one root port.
E.Establishing vlans increases the number of broadcast domains.
F.Switches that are configured with vlans make forwarding decisions based on both layer 2 and layer 3 address information.
S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame Relay topology shown in the exhibit. Originally， static routes were configured between these routers to successfully route traffic between the attached networks. What will need to be done in order to use RIPv2 in place of the static routes？（）
A.Configure the no ip subnet-zero command on R1,R2,and R3.
B.Dynamic routing protocols such as RIPv2 cannot be used across Frame Relay networks.
C.Configure the S0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D.Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E.Change the network address configuration to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25 subnetwork.
最新試題
請參見圖示。一臺主機正使用NAT 連接到Internet。下列哪三項IP 地址可實現此連接？（）
請參見圖示。網絡中的所有設備均使用默認配置。此拓撲中存在多少個廣播域？（）
在配置路由器時，網絡技術人員想要命名路由器。輸入hostname 命令后，技術人員會看到下列哪一項提示？（）
請參見圖示。網絡技術人員試圖確定主機A 的正確IP 地址配置。以下哪一項是主機A 的有效配置？（）
請參見圖示。對于從主機A 向Web 服務器發出的網頁請求，正確的目的套接字數字是什么？（）
PC 無法連接到任何遠程網站，無法ping 通其默認網關，也無法ping 通本地網段中工作正常的打印機。以下哪項操作可以確認此PC 上的TCP/IP 協議棧是否工作正常？（）
請參見圖示。某用戶想要查看當前的配置。圖中所示為ipconfig/all 命令的輸出。從此輸出可以得到哪三項結論？（）
路由器使用哪一項信息來確定源主機和目的主機之間的路徑？（）
請參見圖示。電纜1和電纜2分別按照特定的物理層要求接線。哪三個網段使用電纜2？（）
請參見圖示。主機X 和主機Y 與本地網絡的通信受到限制。此問題的原因是什么？（）