On the Company wireless LAN， A client is searching for an access point （AP）.
What is the correct process order that this Company client and access point goes through in order to create a connection？（）
A. association request/response， probe request/response， authentication request/response
B. association request/response， authentication request/response， probe request/response
C. probe request/response， authentication request/response， association request/response
D. probe request/response， association request/response， authentication request/response
E. None of the other alternatives apply
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. The signal transmitted from the AP is reflected off a wall resulting in multipath interference at the client end.
Which statement is true？ （）
A. The transmitted signal from the AP arrives at the client at slightly different times resulting in phase shifting.
B. If signal 2 is close to 360 degrees out of phase with signal 1， the result is essentially zerosignal or a dead spot in the WLAN.
C. Multipath interference is less of an issue when using a DSSS technology because multipath is frequency selective.
D. If signal 1 is in phase with signal 2， the result is essentially zerosignal or a dead spot in the WLAN.
E. Multipath interference is solved by using dual antennas.
You work as a network technician at Company. Please study the exhibit carefully. In this
Company wireless network， the LAP （lightweight access point） attempts to register to a WLC （Wireless LAN Controller）.
What kind of message is transmitted？（）
A. The lightweight access point will send Layer 2 and Layer 3 Lightweight Access Point （LWAPP） mode discovery request messages at the same time.
B. The lightweight access point will send Layer 3 Lightweight Access Point （LWAPP） mode discovery request messages only.
C. The lightweight access point will send Layer 2 Lightweight Access Point （LWAPP） mode
D.iscovery request messages. If the attempt fails， the LAP will try Layer 3 LWAPP WLC discovery. D. The lightweight access point will send Layer 2 Lightweight Access Point （LWAPP） mode discovery request messages only.
LDAP is being used throughout the Company wireless network.
Which statement about the Lightweight Access Point Protocol （LWAPP） protocol is true？（）
A. The processing of 802.11 data and management protocols and access point capabilities is distributed between a lightweight access point and a centralized WLAN controller.
B. LWAPP advertises its WDS capability and participates in electing the best WDS device for the wireless LAN.
C. LWAPP aggregates radio management forward information and sends it to a wireless LAN solution engine.
D. LWAPP authenticates all access points in the subnet and establishes a secure communication channel with each of them.
E. None of the other alternatives apply
Refer to the exhibit. Both host stations are part of the same subnet but are in different VLANs. On the basis of the information presented in the exhibit，
which statement is true about an attempt to ping from host to host？ （）
A. The two different hosts will need to be in the same VLAN in order for the ping command to be successful.
B. A Layer 3 device is needed for the ping command to be successful.
C. The ping command will be successful without any further configuration changes.
D. A trunk port will need to be configured on the link between Sw_A and Sw_B for the ping command to be successful.
Based on the network diagram and routing table output in the exhibit，
which of these statements is true？ （）
A. InterVLAN routing will not occur since no routing protocol has been configured.
B. InterVLAN routing has been configured properly， and the workstations have connectivity to each other.
C. Although interVLAN routing is not enabled， both workstations will have connectivity to each other.
D. Although interVLAN routing is enabled， the workstations will not have connectivity to each other.
最新試題
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Which router redundancy protocol cannot be configured for interface tracking？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）