A. device PoE requirements
B. device IP address
C. device voice VLAN ID
D. device platform
您可能感興趣的試卷
你可能感興趣的試題
A. an edge port that transitions to the forwarding state
B. a non-edge port that transitions to the blocking state
C. a non-edge port that transitions to the forwarding state
D. an edge port that transitions to the blocking state
E. any port that transitions to the blocking state
F. any port that transitions to the forwarding state
A. active
B. speak
C. learn
D. listen
E. init
F. standby
You administer the network shown above. You issue the show interfaces trunk command on SwitchA and receive the following output：
SwitchA#show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa0/1 desirable -n802.1q trunking 1
Port Vlans allowed on trunk Fa0/1 1-4094
Port Vlans allowed and active in management domain
Fa0/1 1-9，31-37
Port Vlans in spanning tree forwarding state and not pruned
Fa0/1 1-9，31，33-37
Which of the following statements is true regarding VLAN 32？（）
A. VLAN 32 is not allowed on the trunk port.
B. VLAN 32 is not active on the switch.
C. Traffic from VLAN 32 is not being sent over the trunk port.
D. Traffic from VLAN 32 is not restricted to only the trunk ports that require it.
You want to configure a switched internetwork with multiple VLANs as shown above.
Which of the following commands should you issue on SwitchA for the port connected to SwitchB？ （）
A. switchport mode trunk
B. switchport access vlan 5
C. switchport mode access vlan 5
D. switchport trunk native vlan 5
Refer to the exhibit.
Which of the following should you do to configure the IP phone to override the priority of the data packets it receives from the host？ （）
A. Issue the mls qos trust cos command on the switch port connected to the IP phone.
B. Issue the switchport priority extend cos command on the switch port connected to the IP phone.
C. Issue the switchport priority extend cos command on the IP phone.
D. Issue the mls qos trust cos command on the IP phone.
最新試題
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Refer to the exhibit. STP has been implemented in the network. Switch SW_A is the root switch for the default VLAN. To reduce the broadcast domain， the network administrator decides to split users on the network into VLAN 2 and VLAN 10. The administrator issues the command spanning-tree vlan 2 root primary on switch SW_A. What will happen as a result of this change？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
Which three statements about STP timers are true？（）