The fol lowing line of output was extracted from the output of the show ip bgp command on Router R1. Which of the following can be determined from this output?（）
Network Next Hop Metric LocPrf Weight Path
* 130.1.1.0/28 1.1.1.1 0 1 2 3 4 i
A. The route is learne d from an eBGP peer
B. The route has no more than three ASNs in the AS_PatH
C. The route is the best route for this prefix
D. None of these facts can be positively determined by this output
您可能感興趣的試卷
你可能感興趣的試題
The following output occurs on Router R1. Which of the following cannot be determine d from this output?（）
R1# show ip route 180.1.1.0 255.255.255.240
Routing entry for 180.1.1.0/28
Known via "bgp 2", distance 20, metric 0
Tag 3, type external
Last update from 192.168.1.2 00:10:27 ago
Routing Descriptor Blocks:
* 192.168.1.2, from 19 2.168.1.2, 00:10:27 ago
Route metric is 0, traffic share count is 1
AS Hops 2
Route tag 3
A. The type of BGP peer (iBGP or eBGP) that advertised this route to R1
B. R1's ASN
C. The next - hop router's ASN
D. The AS_Path length
A. It lists a set of path attributes, along with a list of prefixes that use those PAs
B. It lists a prefix/length, plus the PA settings for that prefix
C. It lists withdrawn routes, but never in the same Update message as newly advertised routes
D. A single Update message lists at most a single prefix/lengtH
The following output was taken from the show ip bgp command on Router R2. In this case, which of the following commands are most likely to already be configured on R2?（）
BGP router identifier 11.11.11.11, local AS number 11
...
Neighbor V AS Ms gRcvd MsgSent TblVer InQ OutQ Up/Down
State/PfxRcd
1.1.1.1 4 1 87 87 0 0 0 00:00:06 Idle
(Admin)
2.2.2.2 4 3 173 183 41 0 0 00:58:47
A. router bgp 11
B. neighbor 1.1.1.1 remote- as 11
C. neighbor 2.2.2.2 prefix - limit 1
D. neighbor 1.1.1.1 shutdown
The following output, taken from a show ip bgp command on Router R1, lists two neighbors. In what BGP neighbor state is neighbor 1.1.1.1?（）
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down
State/PfxRcd
1.1.1.1 4 1 60 61 26 0 0 00:45:01
0
2.2.2.2 4 3 153 159 26 0 0 00:38:13
1
A. Idle
B. Opensent
C. Active
D. Established
Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively.
Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）
A. router bgp 1
B. neighbor 2.2.2.2 remote- as 2
C. neighbor 2.2.2.2 update - source loopback1
D. neighbor 2.2.2.2 multihop 2
最新試題
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1